Numerical modeling of the hydraulic blade pitch actuator in a spar‐type floating wind turbine considering fault conditions and their effects on global dynamic responses

This paper deals with numerical modeling of the hydraulic blade pitch actuator and its effect on the dynamic responses of a floating spar‐type wind turbine under valve fault conditions. A spar‐type floating wind turbine concept is modeled and simulated using an aero‐hydro‐servo‐elastic simulation tool (Simo‐Riflex [SR]). Because the blade pitch system has the highest failure rate, a numerical model of the hydraulic blade pitch actuator with/without valve faults is developed and linked to SR to study the effects of faults on global responses of the spar‐type floating wind turbine for different faults, fault magnitudes, and environmental conditions. The consequence of valve faults in the pitch actuator is that the blade cannot be pitched to the desired angle, so there may be a delay in the response due to excessive friction and the wrong voltage, or slit lock may cause runaway blade pitch. A short circuit may cause the blade to get stuck at a particular pitch angle. These faults contribute to rotor imbalance, which result in different effects on the turbine structure and the platform motions. The proposed method for combining global and hydraulic actuator models is demonstrated in case studies with stochastic wind and wave conditions and different types of valve faults.     

Morondava盆地西部侏罗纪断陷盆地构造特征

系统分析了Morondava盆地西部侏罗纪断陷盆地构造特征,实可分为东部断陷带、中部断裂构造带和西部侏罗系残留斜坡带,可能存在有断鼻型、背斜型、地层剥蚀尖灭型、断块型、古潜山及岩性圈闭。     

低阶煤热解条件对高炉喷吹半焦燃烧性能及动力学特性的影响

采用热重分析法研究了不同热解条件下半焦的燃烧性能和动力学特征，利用Ozawa法求取动力学参数。结果表明，热解温度越低、保温时间越短时，半焦的燃烧性能越好；热解升温速率对半焦燃烧过程的反应程度影响不大；粒度越大，燃烧性能差异性越明显。热解温度对半焦燃烧性能影响较大，550℃是本研究中制备高燃烧反应性半焦的适宜热解温度。两种不同粒度原煤制得的半焦均随转化率增大，活化能减小。1~3 mm原煤在热解温度为550℃时所得半焦在燃烧过程中符合反应级数模型，化学反应为限制性环节，反应最概然机理函数为f(α)=(1–α)2。     

内蒙古石灰窑沟铁矿地质特征及找矿标志

石灰窑沟铁矿区位于赤峰市北西约80 km处，地处西拉木伦多金属成矿带的南侧，区域位于内蒙古地轴东段与内蒙海西褶皱带接触带，Ⅲ级构造单元为云雾山隆起的北东端和赤峰—铭山大断裂2条构造单元的分界线处，本矿床围岩蚀变具有分带性，是一个受断裂和褶皱复合控制的矽卡岩型矿床。为探讨该矿区的地质特征及找矿标志，通过近几年对本区地质勘查工作的总结分析，认为该矿床为矽卡岩型矿床，围绕构造发育部位，岩体与地层接触带及附近且与高精度磁测异常套合区是主要的找矿标志。     

Numerical analysis on combustion process and sodium transformation behavior in a 660 MW supercritical face-fired boiler purely burning high sodium content Zhundong coal

CHEMKIN software was used to optimize the reaction mechanism of sodium in flue gas to study the influence of targeted design for purely burning Zhundong (ZD) coal on boiler characteristics. Then, the optimized 32-step elemental reaction was combined with CFD software. An eddy-dissipation concept model considering detailed chemical reactions was used to simulate the transformation behavior of sodium-containing substances. The combustion characteristics of the 660 MW face-fired boiler under various loads were also simulated. The field distribution in the furnace and the migration path of sodium along the track of pulverized coal particles were obtained. The results show that the interference between each burner in the furnace is small at the BMCR load, and the phenomenon of “wind wrapping fire” is distinctly clear. The temperature at furnace outlet is approximately 970.98 °C. At a low load, the combustion in the furnace is stable, and the temperature at the furnace outlet reaches the design value. The sodium present in ZD coal is involved in the reaction after it is released in the form of Na and NaCl. Sodium is present in different forms in the main burner zone, mainly NaCl (67%), NaOH (12%), Na (9%), and Na₂SO₄ (7%). The forms of sodium at the furnace outlet are NaCl (50%), Na₂SO₄ (37%), Na₂Cl₂ (9%) and NaHSO₄ (4%). A small amount of Na₂SO₄ is formed by NaHSO₄ reaction in the main burner zone. It then reacts to form NaSO₄, wherein NaHSO₄ is formed by path 2. Na₂SO₄ is mainly generated in the burnout zone through path 1, and paths 2, 3, and 4 are hardly observed. The findings of this research can provide reference for the design of a purely fired ZD coal boiler and further studies on slagging observed on the heating surface.     

Lab-Scale Microreactor Plant for the Study of Methylations with Liquid Chloromethane

Chloromethane is an important reagent for methylations in the process industry. However, as a gas suspected of causing cancer, it is rarely used at laboratory scale. Therefore, a setup is presented here for studies in a laboratory under safe and reproducible conditions. The use of a microreactor guarantees high heat transfer rates and a low holdup of the reagent. As a proof-of-concept, the reaction of chloromethane with the secondary amine morpholine in aqueous solution is investigated. By applying elevated pressures, a liquid-liquid system with enhanced solubility of chloromethane in the aqueous phase is accessible.     

煤/石油焦共气化过程中AAEM的催化转化行为

以富含碱金属及碱土金属的准东煤和石油焦为原料,在热重反应器上分别进行了水蒸气及CO2条件下的共气化实验,探究了AAEM的赋存形态对其转化行为及燃料气化特性的影响规律.研究表明,准东煤与石油焦在水蒸气条件下的共气化反应速率明显快于CO2条件,来自煤中的AAEM促进了石油焦的气化.在CO2气氛中,不同赋存形态矿物的催化作用存在较大差异,盐酸溶态的Ca起主要催化作用,并在气化过程中生成CaS.而在水蒸气气氛中,不同赋存形态矿物的催化作用差异较小,气化过程中含Ca组分主要生成CaO.     

基于永磁涡流传动的长距离带式输送机启动特性研究

针对矿用带式输送机启动过程易出现打滑、淤带和断带等问题,基于永磁涡流传动技术,将双盘式磁力耦合器作为带式输送机的驱动装置,建立双盘式磁力耦合器动态数学模型,运用AMEsim软件搭建带式输送机系统仿真模型,设置启动时间分别为60、80和100 s,采用Harrison控制曲线启动时,研究带式输送机满载启动时机头、机尾部输送带的速度特性和张力特性,张紧装置位移特性以及双盘式磁力耦合器调速气隙特性,仿真结果表明:当启动时间为60 s时,带式输送机输送带速度波动大,动张力明显,尾部输送带最大张力达到29 kN,启动过程不平稳;双盘式磁力耦合器调速时,气隙变化与带式输送机启动速度变化趋势相反,启动过程气隙从22 mm减小到4 mm;当启动时间为80 s和100 s时,带式输送机启动过程相对平稳,速度和张紧装置位移波动小,尾部输送带张力波动幅度分别为5 kN和3 kN;带式输送机启动过程存在最佳启动时间,继续延长时间,对带式输送机启动特性影响越来越小,80 s可作为合理启动时间。     

Study on wax precipitation characteristics of wax deposit in pipes

Wax deposit properties are a significant concern in pipeline pigging during waxy crude oil transportation. In the present work, the impacts of flow conditions and oil properties on the wax precipitation characteristics of wax deposits are investigated. A flow loop apparatus was developed to conduct wax deposition experiments using four crude oils collected from different field pipes. The differential scanning calorimetry (DSC) technique was employed to observe the wax precipitation characteristics of crude oil and wax deposit. The results show that the wax content and the wax appearance temperature (WAT) of the deposits increase with shear stress and radial temperature gradient, and decrease with radial wax molecule concentration gradient near the pipe wall. The DSC tests on the wax deposits revealed that the deposit wax content is strongly correlated to the oil wax content. Furthermore, an empirical correlation was developed to predict the wax content and the WAT of the wax deposit. Verification of the empirical correlation using the different oils indicated that the average relative error of the wax content prediction and average absolute error of WAT prediction were 13.2% and 3.6°C, respectively.     

Materialwissenschaftliche Analyse des Abbindeverhaltens von Holzklebstoffen am Beispiel von 1K-PUR

The curing of wood adhesives has so far been evaluated on a basis of parameters, which offer process optimization only to a small degree. However, the curing becomes analyzable in detail by using oscillation measurements and a test setup adapted to the bonding process. With time sweep measurements, the adhesion process can be divided into characteristic ranges of molecular and structural processes. This method is presented and analyzed using a polyurethane prepolymer for joining wood-based materials.